D-Link DI-304M Guide de l'utilisateur Page 77
- Page / 117
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
71
CopperHead 3400
User Guide
This display cycle repeats itself and depending on timing may start with
either OPT of the strength measurement - BOPT does not reappear in the
repeating cycle.
DIAGNOSTIC MODE Temperature (TEMP)
DIAG When first entering the Diagnostic mode the DIAG display mode indicator
LED will blink – the first sub-mode is TEMP (Temperature). The Digital
Display Characters will glow Green when the temperature is normal and
Red when outside of normal range.
DIAG/TEMP TEMP Indicates the display is in the TEMP sub-mode
DIAG/TEMP PS The Power Supply (PS) temperature will be displayed
DIAG/TEMP TEMP Repeats that the display is in the TEMP sub-mode
DIAG/TEMP 37C Temperature display in Centigrade for Power Supply circuit board
DIAG/TEMP BASE The Base Station main circuit board temperature will be displayed
DIAG/TEMP TEMP Repeats that the display is in the TEMP sub-mode
DIAG/TEMP 47C Temperature display in Centigrade for Base Station circuit board
DIAG/TEMP PS The Power Supply (PS) temperature will be again displayed
DIAG/TEMP TEMP Repeats that the display is in the TEMP sub-mode
DIAG/TEMP 36C Temperature display in Centigrade for Power Supply circuit board
This display cycle repeats until the Display Mode selector is pushed
DIAGNOSTIC MODE Power Supply Voltage Status (POWER)
DIAG/POWER A quick push of the Display Mode selector advances to the Power (POWR)
diagnostic sub-mode. Digital Display Characters are Green when all power
levels are normal and Red when any power level is outside normal level
DIAG/POWER POWR Indicates the display is in the POWER sub-mode
DIAG/POWER BASE Indicates that the Base Station main controller board is being measured
DIAG/POWER POWER Indicates the display is in the POWER sub-mode
DIAG/POWER OK Indicates that the item is in an OK State
DIAG/POWER DISP Indicates that the LED Display controller board is being measured
DIAG/POWER POWER Indicates the display is in the POWER sub-mode
DIAG/POWER OK Indicates that the item is in an OK State
DIAG/POWER CHAR Indicates that the four-character controller board is being measured
DIAG/POWER POWR Indicates the display is in the POWER sub-mode
DIAG/POWER OK Indicates that the item is in an OK State
DIAG/POWER AUD Indicates that the Audio controller board is being measured
DIAG/POWER POWR Indicates the display is in the POWER sub-mode
DIAG/POWER OK Indicates that the item is in an OK State
DIAG/POWER VBS Indicates that the VBS (analog Video) controller board is being measured
Display Mode
Typical
Readout
Base Station Digital Display Activity Explanation
- CopperHead 3400 User Guide 1
- Terms and Conditions 2
- Table of Contents 3
- Introduction 7
- Product Returns 9
- Safety Information 10
- System Overview 11
- Fiber Cable Concepts 12
- Fiber Optic Connector Types 13
- Camera Unit Overview 16
- Base Station Overview 16
- Camera Unit 20
- Area A – Connector Panel 21
- Camera Unit Front Components 22
- Fan Diagnostic Mode 25
- High Temperature Warning 25
- Camera Unit Rear Components 26
- Area C - Intercom Controls 28
- Area E – Fiber Connector 29
- Area F – Battery Mount 30
- Base Station 31
- Fig. 3-17: Audio Indicators 32
- Base Station Front Panel 34
- Base Station Rear Panel 35
- Fig. 3-22: Connector panels 36
- Clear-Com Intercom Module 39
- Power Wafer Camera Adaptor 40
- PowerPlus Camera Adaptor 42
- HDX Power Unit 43
- GrassValley 50
- on page 45 50
- Grass Valley 57
- Grass Valley supplied cables 57
- Equipment connections 65
- Powering the System 71
- Audio Control Switches 74
- Using the Digital Displays 75
- Grass Valley, a Belden 78
- Best Practices 83
- Troubleshooting 84
- Specifications 85
- Dimensions (WxLxD) 87
- Weight 87
- Contact Us 89
- Connector Pin Assignments 90
- Base Station Connectors 91
- Tally/GPI/Data 92
- Clear‐ComIntercom 92
- RTSIntercom 92
- Camera Unit Connectors 95
- CameraHeadset 96
- AudioOutput 96
- AudioInput 96
- CopperHead 3400 100
- Available Accessories 102
- Units and Connectors 103
- Wider Illustrations 104
- Adaptors and Plugs 105
- User Guide 106
- Plates, Panels, and Cables 108
- Camera Signal Cables 109
- Base Station Cables 109
- Camera Remote Control Cables 110
- Diagrams 112
- Camera Unit Intercom Controls 115
- Camera Unit Fan Control 115
- Camera Unit Indicators 115
- Block Diagram 116
Produits connexes et manuels pour Mise en réseau D-Link DI-304M
(96 pages)
(2 pages)
(107 pages)
(164 pages)
(40 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.080 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels