D-Link DS-510S Guide de l'utilisateur

DS-510 User's Guide

1 AC adapter2 Power cord3 USB cableParent topic: Scanner Parts LocationsScanner Buttons and LightsButtons1The power button2The stop button3 The start

Lights1 The ! error light2 The Ready lightParent topic: Scanner Parts LocationsPage Separation LeverYou can scan plastic cards, folded documents, enve

Move the separation lever to this position only when scanning plastic cards, folded documents,envelopes, or any document that requires an optional car

Part Part numberRoller assembly kit B12B813561Parent topic: Scanner BasicsChanging the Power Off and Sleep Timer SettingsYou can use the Epson Scan Se

Placing Originals on the ScannerFollow the instructions here to place your originals on the scanner.Caution: Do not place anything on top of your scan

3. Slide the input tray edge guides all the way out.4. Check to make sure that the page separation lever is in the position shown here.Note: To preven

5. If you are loading a multi-page document, fan your stack of originals and tap them gently on a flatsurface to even the edges.6. Slide your original

7. Slide the edge guides against the edges of the original.Original Document Loading CapacityParent topic: Placing Originals on the ScannerRelated ref

Paper size Paper weight Paper type Loading capacityLetter (8.5 × 11 inches 13 to 35 lb (50 Plain paper 13 lb (50 g/m²): 70 sheets[216 × 279 mm]) to 13

• Transparencies• Glossy originalsParent topic: Loading Originals in the Input TrayLoading Plastic Cards in the Input TrayYou can load plastic cards t

3. Slide the input tray edge guides all the way outward.4. Load one plastic card horizontally in the input tray as shown, sliding it in until it meets

5. Slide the edge guides against the edges of the plastic card.21

6. Set the page separation lever to the position shown here.Note: To prevent paper jams, make sure to set the separation lever back to its original po

Loading direction HorizontalNote: Plastic cards with glossy surfaces may not scan properly.Parent topic: Loading Plastic Cards in the Input TrayLoadin

3. Slide the input tray edge guides all the way out.4. Do one of the following to load your original:• Load a large or thick original or an envelope i

• For a folded original, fold and load the original as shown.Caution: Do not load the document with the open side facing down.• For a photo or an irre

• If the original is larger than the carrier sheet, fold it in half with the sides to be scanned facingout. Position the right side of the original at

6. Slide the edge guides against the edges of the sheet.7. Set the page separation lever to the position shown here.Note: To prevent paper jams, make

Large or Thick Original Loading CapacityParent topic: Placing Originals on the ScannerRelated referencesPage Separation LeverRelated topicsScanningLar

Using the Network Interface UnitSee these sections to use the optional Epson Network Interface Unit to scan over a network.Network Interface Unit Part

ContentsDS-510 User's Guide ...

Connecting the Network Interface UnitSee the documentation that came with the optional Epson Network Interface Unit for instructions onconnecting it t

4. Do one of the following:• Under Search for addresses, select the IP address of your Network Interface Unit, and click OK.• Select the Enter address

Parent topic: Using the Network Interface UnitScanning to Network Computers from the Network Interface Unit - WindowsYou can scan to a network compute

ScanningYou can scan original documents or photos and save them as digital files.Starting a Scan from a Scanner ButtonScanning with Document Capture P

1. Start Document Capture Pro or Document Capture on a computer connected to the scanner.2. Click the Manage Job icon from the toolbar at the top of t

2. Click the Scan icon.You see a window like this:35

Note: If you want to use a scan job that you created instead, select it from the Job list in theDocument Capture Pro or Document Capture window, click

You see a preview of your scan in the Document Capture Pro (Windows) or Document Capture (OSX) window.6. Check the scanned images and edit them as nec

2. Select options for each of the scan settings on the screen.3. If necessary, click the Preview button.Epson Scan previews your original, and display

6. Click Scan.You see the File Save Settings window.7. Change any of the necessary file save settings and click OK.Epson Scan scans your original, and

Scanning Using OCR - Windows ... 45Scanning Using OCR - OS

Color EnhanceEnhances the red, green, or blue shades in the scanned image.BrightnessAdjusts the overall lightness and darkness of the scanned image.Co

3. Do one of the following to access the Epson Scan settings:• Windows: Click the Scan icon, then click Detailed Settings.• OS X: Open the Scan menu a

4. Select Double-Sided as the Document Source setting.5. Select the original document size as the Size setting.6. Select one of the following as the S

8. Click Scan.The scanned image is displayed.Note: If the scanned images are not stitched together correctly, click Configuration on the EpsonScan win

3. Click the Scan icon.4. Select any displayed scan settings you want to use.Note: See the Help information in Document Capture Pro for details.5. Cli

Loading Plastic Cards in the Input TrayLoading Special DocumentsConvert Scanned Documents to Editable Text (OCR)You can scan a document and convert th

3. Select the language used in the document you are going to scan as the Document Languagesetting.4. Click either the Scan to Other Formats icon or th

Your document is scanned and processed into editable text, then you see the Save As window.10. Select a name and a file format for your document and c

3. Open the Get Images From pop-up menu and select your product.4. Select the language used in the document you are going to scan as the Document Lang

• Windows (other versions): Click or Start, and select All Programs or Programs. SelectEPSON Software, then select Document Capture Pro.• OS X: Open t

Technical Specifications ... 77

5. Click one of the cloud service Destination icons to choose where to save your scanned file. (If youcannot see all of the icons below, the service s

Cleaning and Transporting Your ScannerSee these sections if you need to clean or transport your scanner.Cleaning Your ScannerCleaning Inside Your Scan

3. Pull down on the cover open lever and open the scanner cover.4. Use a soft, dry cloth to wipe off any dust or dirt on the rollers inside the scanne

5. Wipe off any dust or dirt on the pickup rollers.6. Plug in the AC adapter and press the power button to turn on the scanner.7. Hold down the start

9. Wipe off any dust or dirt on the glass scanning surfaces using a soft, dry cloth. If the glass surface isstained with grease or some other hard-to-

3. Click Maintenance.You see a screen like this:4. You can check the scanner roller counter by reading the number in the Number of Scans field. If the

4. Pull down on the cover open lever and open the scanner cover.5. Squeeze the tab on the right side of the pickup roller cover and open the cover.Cau

6. Slide the pickup rollers to the right and remove them.57

7. To install the new lower pickup roller, align the notches on the roller and slide it to the left.8. To install the new upper pickup roller, align t

10. Press down on the separation roller cover latch inside the scanner cover and pull down the cover toopen it.Caution: Be careful not to apply too mu

13. Slide the new separation roller onto the spindle as shown. Make sure that the notches on the rollerand spindle align properly.Note: Check that the

15. While applying gentle pressure on the separation roller, close the separation roller cover.Note: If you are not able to close the cover, the rolle

4. Click Reset.The number of scans changes to 0 (zero).5. Click OK.Parent topic: Replacing the Scanner RollersTransporting Your ScannerIf you need to

Solving ProblemsCheck these sections for solutions to problems you may have using your product.Scanner Light StatusSolving Scanning ProblemsSolving Ne

Light status Condition/solutionThe Ready light is on The scanner is turned on and ready to scan.The Ready light is flashing The scanner is scanning or

Scanner Does Not Turn On or Turns Off UnexpectedlyIf the scanner does not turn on or if it turns off unexpectedly, try these solutions:• Make sure the

Related tasksUninstalling Scanner Software - WindowsUninstalling Scanner Software - OS XCannot Start Epson ScanIf you cannot start Epson Scan, try the

• Remove the originals, fan the edges to separate the sheets, if necessary, and reload them.• Load only originals that meets the specifications for yo

4. Gently pull out any jammed originals from inside the scanner.5. Gently pull out any jammed originals from the output tray.68

6. Close the scanner cover.7. Carefully follow all loading instructions when you reload originals.Parent topic: Solving Scanning ProblemsRelated tasks

DS-510 User's GuideWelcome to the DS-510 User's Guide.For a printable PDF copy of this guide, click here.7

• Windows (other versions): C:\Users\(user name)\AppData\Local\TempParent topic: Solving Scanning ProblemsSolving Network Interface Unit ProblemsIf yo

Back of Original Image Appears in Scanned ImageIf an image from the back of a thin original appears in your scanned image, make sure you selected thec

Parent topic: Solving Scanned Image Quality ProblemsRelated referencesAvailable Image AdjustmentsRelated tasksScanning with Epson ScanRipple Patterns

5. Wipe off any stains on the glass scanning surfaces using a soft, dry cloth.Note: If the glass surfaces are stained with grease or some other hard-t

7. Plug in the AC adapter.Parent topic: Solving Scanned Image Quality ProblemsRelated tasksCleaning Inside Your ScannerScanned Image Edges are Cropped

2. Disconnect any interface cables.3. Do the following to uninstall each of your scanning software programs, then follow any on-screeninstructions:• W

Parent topic: When to Uninstall Your Scanner SoftwareWhere to Get HelpIf you need to contact Epson for technical support services, use the following s

Technical SpecificationsThese sections list the technical specifications for your scanner.Note: Epson offers a recycling program for end of life produ

Interface Macintosh USBDisplay Color monitor with 800 × 600 resolution or higher and millions ofcolorsNote: Epson Scan does not support the UNIX File

Dimension SpecificationsHeight 6.1 inches (154.0 mm)Width 11.7 inches (297.0 mm)Depth 6.0 inches (152.0 mm)Weight Approx. 5.5 lb (2.5 kg)Note: Dimensi

Scanner BasicsSee these sections to learn about the basic features of your scanner.Scanner Parts LocationsUser Replaceable Epson Scanner PartsChanging

Rated output voltage DC 24 VRated output current 1.37 AParent topic: Technical SpecificationsEnvironmental SpecificationsTemperature Operating: 41 to

AC AdapterUnited States Safety: UL60950-1EMC: FCC part 15 Subpart B Class BCanada Safety: CAN/CSA C22.2 No. 60950-1EMC: CAN/CSA-CEI/IEC CISPR 22 Class

NoticesCheck these sections for important notices about your scanner.Note: Epson offers a recycling program for end of life products. Please go to eps

• Use only the type of power source indicated on the AC adapter's label, and always supply powerdirectly from a standard domestic electrical outl

Restrictions on CopyingObserve the following restrictions to ensure responsible and legal use of your scanner.Copying of the following items is prohib

General Notice: Other product names used herein are for identification purposes only and may betrademarks of their respective owners. Epson disclaims

Copyright © 1991-1997 Silicon Graphics, Inc.Permission to use, copy, modify, distribute, and sell this software and its documentation for any purposei

FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIALDAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS ORSE

1 Scanner cover2 Page separation lever3 Edge guides4 Input tray extension5 Input tray6 Cover open lever7 Output tray8 Output tray extension1 Kensingto