D-Link 502G - DSL Router - EN Guide de l'utilisateur Page 16
- Page / 73
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
DSL-502T ADSL Router User’s Guide
6
2
Hardware Installation
The DSL-502T maintains three separate interfaces, an Ethernet, a USB and an ADSL interface.
Place the Router in a location where it can be connected to the various devices as well as to a
power source. The Router should not be located where it will be exposed to moisture or excessive
heat. Make sure the cables and power cord are placed safely out of the way so they do not create a
tripping hazard. As with any electrical appliance, observe common sense safety procedures.
The Router can be placed on a shelf or desktop, ideally you should be able to see the LED
indicators on the front if you need to view them for troubleshooting.
Power on Router
CAUTION: The Router must be used with the power adapter included with the device.
To power on the Router:
1. Insert the AC Power Adapter cord into the power receptacle located on the rear panel of the
Router and plug the adapter into a suitable nearby power source.
2. You should see the Power LED indicator light up and remain lit. The Status LED should light
solid green and begin to blink after a few seconds.
3. If the Ethernet port is connected to a working device, check the Ethernet Link/Act LED
indicators to make sure the connection is valid. The Router will attempt to establish the ADSL
connection, if the ADSL line is connected and the Router is properly configured this should light
up after several seconds. If this is the first time installing the device, some settings may need
to be changed before the Router can establish a connection.
Factory Reset Button
The Router may be reset to the original factory default settings by depressing the reset button for
a few seconds while the device is powered on. Use a ballpoint or paperclip to gently push down the
reset button. Remember that this will wipe out any settings stored in flash memory including user
account information and LAN IP settings. The device settings will be restored to the factory default
IP address 10.1.1.1 and the subnet mask is 255.0.0.0, the default management Username is
admin and the default Password is admin.
Network Connections
Network connections are provided through the ADSL port, the Ethernet port and the USB port on
the back of the Router. See the Rear Panel diagram above and the illustrations below for examples.
See Installing the USB Driver above for a description of the USB driver installation procedure.
Connect ADSL Line
Use the ADSL cable included with the Router to connect it to a telephone wall socket or receptacle.
Plug one end of the cable into the ADSL port (RJ-11 receptacle) on the rear panel of the Router and
insert the other end into the RJ-11 wall socket. If you are using a low pass filter device, follow the
instructions included with the device or given to you by your service provider. The ADSL connection
- DSL-502T 1
- ADSL Router 1
- User ‘s Guide 1
- FCC Warning 2
- CE Mark Warning 2
- Table Of Contents 3
- Before You Start 5
- Packing List 5
- Installation Requirements 6
- Installing the USB Driver 9
- Introduction 11
- Router Features 12
- Front Panel Display 14
- Rear Panel 15
- Hardware Installation 16
- Connect Router to Ethernet 17
- Basic Router Configuration 18
- Windows 2000 21
- Windows ME 22
- Windows 95 and Windows 98 22
- Windows NT 4.0 Workstations 23
- Login to Home Page 24
- Configure the Router 25
- Using the Setup Wizard 26
- Configure WAN Connection 30
- Bridged Connection for WAN 32
- Static IP Address for WAN 33
- Configure Multiple PVCs 34
- Configure new VC 35
- LAN IP Settings 36
- Use the Router for DHCP 37
- Disable the DHCP Server 37
- DNS Server Settings 38
- Save Settings and Reboot 39
- Advanced Router Management 40
- Enable UPnP Menu 41
- Port Forwarding 42
- Filters 45
- Firewall 47
- NAT Enable/Disable Menu 48
- Static Routing 50
- Dynamic Routing (RIP) 51
- Remote Access 52
- Tools and Utilities 53
- Change System Password 53
- Time Configuration 55
- Firmware Upgrade 56
- Ping Test 57
- Diagnostic Test 57
- Router Status Information 59
- Device Information Display 59
- DHCP Clients 60
- Traffic 61
- Technical Specifications 62
- IP Address Setup 64
- Using DHCP 65
- IP Concepts 66
- Subnet Mask 68
- Microfilters and Splitters 69
- Line Splitter 70
- Offices 71
Produits connexes et manuels pour Mise en réseau D-Link 502G - DSL Router - EN
(40 pages)
(109 pages)
BNC 1621M podręczniki
Instrukcje obsługi i podręczniki użytkownika dla Urządzenia pomiarowe BNC 1621M.
Dostarczamy 1 pdf podręczników BNC 1621M do pobrania za darmo według typów dokumentów: Instrukcja Użytkownika
Commentaires sur ces manuels