D-Link DES-3225G Manuel d'utilisateur Page 34
- Page / 219
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
24-port NWay Ethernet Switch User’s Guide
20 Connecting The Switch
4
C
ONNECTING
T
HE
S
WITCH
This chapter describes how to connect the DES-3225G to
your Fast Ethernet network.
Switch to End Node
End nodes include PCs outfitted with a 10, 100 or 10/100
Mbps RJ-45 Ethernet/Fast Ethernet Network Interface
Card (NIC) and most routers. The RJ-45 UTP ports on NICs
and most routers are MDI-II. When using a normal
straight-through cable, an MDI-II port must connect to an
MDI-X port.
An end node can be connected to the Switch via a two-pair
Category 3, 4, 5 UTP/STP straight cable (be sure to use
Category 5 UTP or STP cabling for 100 Mbps Fast Ethernet
connections). The end node should be connected to any of
the twenty-two ports (1x - 22x) of the DES-3225G or to
either of the two 100BASE-TX ports on the front-panel
module that came preinstalled on the switch. An end node
should not be connected to an Uplink port (unless using a
crossover cable), and if the top Uplink port is in use, Port
- DES-3225G 1
- DES-3225GF 1
- 24-Port Fast Ethernet 1
- User’s Guide 1
- Wichtige Sicherheitshinweise 2
- Limited Warranty 4
- Software: 5
- Trademarks 7
- Copyright Statement 7
- FCC Warning 7
- CE Mark Warning 7
- VCCI Warning 8
- BSMI Warning 8
- Overview of this User’s Guide 13
- About This Guide 14
- NTRODUCTION 15
- Gigabit Ethernet Technolog 16
- Switching Technolog 17
- Features 18
- Performance features 19
- NPACKING AND 21
- Installation 22
- Rack Installation 23
- Power on 24
- Power Failure 25
- DENTIFYING 26
- OMPONENTS 26
- Rear Panel 27
- Side Panels 28
- Optional Plug-in Modules 29
- 100BASE-FX Fiber Module 30
- 1000BASE-SX Gigabit Module 31
- LED Indicators 32
- ONNECTING 34
- Switch to Hub or Switch 35
- 22 Connecting The Switch 36
- 10BASE-T Device 37
- 100BASE-TX Device 37
- Switch Management Concepts 39
- IP Addresses and SNMP 40
- Community Names 40
- 28 Switch Management Concepts 42
- Packet Forwarding 44
- Filtering Database 45
- Spanning Tree Algorithm 46
- On the Bridge Level 47
- On the Port Level 48
- Illustration of STA 50
- Port Trunking 52
- 40 Switch Management Concepts 54
- MAC-based VLANs 55
- Port-based VLANs 56
- VLAN Segmentation 57
- Graphics 58
- Workstations 58
- 46 Switch Management Concepts 60
- 48 Switch Management Concepts 62
- Broadcast Storms 63
- Segmenting Broadcast Domains 64
- Eliminating Broadcast Storms 64
- SING THE 66
- NTERFACE 66
- Console Usage Conventions 67
- User Accounts Management 70
- Saving Changes 71
- By Registered Users 73
- View/Delete User Accounts 75
- Setting Up The Switch 76
- Configure IP Address 77
- Configure Console 79
- Advanced Settings 82
- Configure Ports 83
- Configure Slot1 Module 87
- Configure Slot2 Module 90
- Configure Port Mirroring 92
- STP Parameter Settings 94
- STP Port Contro 98
- Using the Console Interface 101
- Configure IGMP Filtering 104
- Configure VLAN 108
- Configure MAC-Based VLA 110
- Configure Trunk 118
- System Utilities 121
- Save Settings to TFTP Server 123
- SNMP Manager Configuration 125
- Switch Monitoring 127
- Traffic Statistics 128
- Port Traffic Statistics 130
- Port Packet Error Statistics 131
- Browse Address Table 135
- Browse IGMP Status 136
- Switch History 138
- Resetting the Switch 139
- Restart System 140
- Factory Reset 140
- ANAGEMENT 142
- Getting Started 143
- Management 143
- Configure Switch 144
- IP Settings 145
- Port Settings 146
- Port Mirroring 149
- Switch Settings 150
- Advanced 152
- Configure 153
- Permanent Address Table 155
- Permanent Multicast Filtering 157
- Multicast Forwarding Table 159
- Spanning Tree 161
- IGMP Filtering 166
- Configure 802.1Q IGMP 167
- Configure VLAN Mode 169
- Configure 802.1Q VLA 172
- Configure Management 176
- User Accounts 178
- Console Port Settings 179
- Switch Overview 181
- Port Statistics 182
- Traffic in Bytes: 183
- Traffic in Frames: 183
- Other errors: 184
- Packet Analysis 186
- Utilization 188
- Reset and Update 192
- Reset to Factory Default 193
- Update Firmware 194
- Change Configuration File 195
- Upload Log File 197
- Save Changes 198
- ECHNICAL 199
- PECIFICATIONS 199
- Physical and Environmental 200
- Performance 201
- PECIFICATION 202
- RJ-45 Pin Specification 189 203
- ONFIGURATION 204
- Sample Configuration File 191 205
- 192 Sample Configuration File 206
- WITCHING 207
- OFTWARE 207
- Index 195 209
- 196 Index 210
- Index 197 211
- 198 Index 212
- Index 199 213
- 200 Index 214
- Index 201 215
- Offices 216
- U.K. D-LINK EUROPE 217
- U.S.A. D-LINK U.S.A 217
- Registration Card 218
Produits connexes et manuels pour Commutateurs de réseau D-Link DES-3225G
(15 pages)
(42 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.219 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels