DSL-100D ADSL PCI Modem User’s Guide First Edition Version 2 (February 2001) 6DSL100D..02
2 Operating Systems: • Windows 95, 95 OSR2 • Windows 98, 98 second edition • Windows 2000 • Windows Me • Windows NT 4.0 NOTE: You will need the
3 Internet Service Protocol Your Internet Service Provider (ISP) uses one of the protocols listed below. Look over the information provided by your
4 Configuration Form Before beginning the installation, photocopy or print this page and fill out the form provided. Refer to this form when you rea
5 Step 1 Hardware Installation The card must be installed on the computer’s mainboard. Since this is an electrical device, safety is important. Fir
6 Step 2 Software Installation and Configuration Windows automatically detects new hardware when it is added to the computer. The Add New Hardware W
7 Windows 98/98SE Driver Installation 1. The Add New Hardware Wizard window automatically appears and indicates that the new PCI Network Controlle
8 5. Find the folder 1483w98, 1577w98, or 2364w98 (according to the protocol used by your ISP) on the CD-ROM drive and click OK. 6. Again the Add
9 8. You must restart the computer to finish the installation. You can do that now if you wish. 9. If you install the RFC2364 (PPPoA) driver, a
10 2. You will need to search for the driver. Click Other Locations… to continue. 3. In the Select Other Location window, click Browse to search
11 5. The driver is now ready to be installed. Click Finish to install it. 6. You must restart the computer to finish the installation. You can
12 2. The Found New Hardware Wizard explains that it can install the driver for the Network Controller (PCI Modem). Select “Search for a suitable d
13 5. Find the folder 1483w2k, 1577w2k, or 2364w2k (according to the protocol used by your ISP) and double-click on it to open it. Or highlight it
14 8. The driver is now ready to be installed. Check to be sure the driver file path is correct and click Next. 9. A warning appears telling you
15 Windows ME Driver Installation 1. The Add New Hardware Wizard window automatically appears and indicates that the new PCI Network Controller (P
16 4. The location of the driver is now listed. Click Next. 5. Again the Add New Hardware Wizard window appears indicating the location of the dr
17 7. You must restart the computer to finish the installation. You can do that now if you wish. 8. If you install the RFC2364 (PPPoA) driver,
18 4. Click the Have Disk button to search for the driver. 5. Insert the driver CD and click OK. Assuming your CD-ROM drive is labeled the D drive
19 7. The Setup Message window tells you that Remote Access Services will be installed. Click OK. 8. Replace the driver CD with the NT 4.0 CD.
20 11. In the Configure Port Usage window, select ‘Dial out only’ and click OK. 12. You are again asked to confirm the selection. Click Continue.
21 Configure Modem The third step of the installation procedure is to configure the Modem. The configuration process is identical for all Windows o
i Trademarks Copyright 2000 D-Link Corporation. Contents subject to change without prior notice. D-Link is a registered trademark of D-Link Corpor
22 2. In the Configuration menu, you will need to choose the ADSL connection mode as instructed by your ADSL service provider. Select ANSI T1.413 Is
23 Configure Modem for Windows 2000 To configure the Modem for the Windows 2000 environment, follow these steps: 1. After you have installed t
24 3. In the PVC Table window you will see your ADSL service provider listed as well as the default VPI/VCI settings, the ADSL protocol (RFC 2364 P
25 5. The PVC Table will again appear with a summary of the PVC settings. Check them again to be certain they are correct and click Close to exit
26 Step 3 Connect to Internet How you connect to the Internet using ADSL is effected by which protocol is used to establish that connection. The in
27 2. You now need only to provide a User Name and Password, no other information is required. The sample window pictured below appears on a PC r
28 For RFC 1483 and RFC 1577 Users If your ADSL connection uses either the RFC 1483 or the RFC 1577 protocol, you must set your own TCP/IP config
2 Windows 2000 (RFC 1483/RFC 1577) 1. Double-click on the My Computer icon, then the Control Panel icon, and then the Network and Dia
3 Modem Indicators Diagnostic Icon Function Once you have installed the software driver a new Diagnostic Tool icon will appear in the lower right co
4 Appendix A TECHNICAL SPECIFICATIONS Interfaces: Edge connector for PCI bus; two RJ-11 jacks (ADSL connection and telephone connection). Standards
ii BSMI Warning Limited Warranty Hardware: D-LINK WARRANTS EACH OF ITS HARDWARE PRODUCTS TO BE FREE FROM DEFECTS IN WORKMANSHIP AND MATERIALS UNDER
Offices AUSTRALIA D-LINK AUSTRALASIA Unit 16, 390 Eastern Valley Way, Roseville, NSW 2069, Australia TEL: 61-2-9417-7100 FAX: 61-2-9417-
JAPAN D-LINK JAPAN 10F, 8-8-15 Nishi-Gotanda, Shinagawa-ku, Tokyo 141 Japan TEL: 81-3-5434-9678 FAX: 81-3-5434-9868 URL: www.d-link
Registration Card Print, type or use block letters. Your name: Mr./Ms__________________________________________________________________________ Orga
iiiSYSTEM/PLATFORM SOFTWARE AND ASSOCIATED REFERENCE MATERIALS. D-LINK MAKES NO WARRANTY THAT ITS SOFTWARE PRODUCTS WILL WORK IN COMBINATION WITH
TABLE OF CONTENTS ABOUT THIS GUIDE...
iiAbout This Guide Congratulations on your purchase of the ADSL PCI Modem Card for Windows® 95, 98, 2000 Me and NT 4.0. This internal modem card con
1 Introduction This section describes the ADSL PCI modem card, its features, and system requirements. Features The ADSL PCI Modem Card is an intern
Commentaires sur ces manuels